Enerdrive B-TEC 36V 100Ah Lithium Battery

Specifications

SKU EPL-100BT-36V

Brand Enerdrive

GTIN 9342616019672

Warranty Period: 5 Years

Product Category Batteries

Battery Voltage 36V

Amp Hours (ah) 100

Battery Length (mm) 519

Battery Width (mm) 273

Battery Height (mm) 222

Battery Weight (kg) 37.7

Model EPL-100BT-36V

Nominal Voltage 38.4V

Nominal Capacity 100Ah

Cycle Life (DOD – 80% under controlled conditions) ≥ 2000 Cycles

Battery Charge Temperature 0 ̴ 45°C

Normal Charge Voltage CV/CC* 43.20 ̴ 43.80V

Standby (Float) Voltage 40.5 ̴ 41.40V

Maximum Charge Current 50A @ 25°C for 30mins

Recommended Charge Current for Maximum Life ≤ 33A

Battery Discharge Temperature -20 ̴ 60°C

Battery Output Voltage Range 33.00 ̴ 48.80V

Maximum Discharge Current 100A @ 25°C ± 5°C for 30mins

Pulse Discharge Current 450A for 1.0s

Discharge Cut-off Voltage ≤ 33.60V

Over-Charge Protection Per Cell 3.90V ± 0.03V

Over-Charge Release Per Cell 3.60V ± 0.05V

Over-Charge Release Method Discharge below release voltage

Over-discharge Protection Per Cell 2.80V ± 0.05V

Over-discharge Release Per Cell 3.20V ± 0.05V

Over-discharge Release Method Apply Charge/Voltage ≥38.4V

Discharge Over Current 110A for 30s – 450A for 1s

Protection Reset Time 5s Auto Release

Over Current Release Method Disconnect Load

Battery Charge Over Temperature Protection to 55°C ± 5°C, Release at 45°C ± 5°C

Battery Discharge Over Temperature Protection to 65°C ± 5°C, Release at 50°C ± 5°C

Short Circuit Protection Auto release after 5s

Case Construction Hi Impact ABS Plastic

Temperature & Humidity Range ≤ 30 days -20°C ̴ 60°C, 5 ̴ 75% RH, ≥ 90 days -10°C ̴ 45°C, 5 ̴ 75% RH

Videos

Enerdrive B-TEC Lithium Batteries - Part 1 - Application

Enerdrive B-TEC Lithium Batteries - Part 2 - Specifications

Enerdrive B-TEC Lithium Batteries - Part 3 - Installation

Enerdrive B-TEC Lithium Batteries - Part 4 - Settings

Enerdrive B-TEC Lithium Batteries - Part 5 - Operation

Enerdrive B-TEC Lithium Batteries - Part 6 - Fault Finding

The Best Caravan Battery?

What Will My Camping Battery Run?

Expanding Your Enerdrive B-TEC Capacity: Enerdrive Batteries in Parallel

How To: Resetting A Flat Enerdrive BTEC or eLITE Battery

Exploring The Enerdrive BMS Found Internally In Their Lithium Batteries

Lithium Batteries Australia - Are they Safe

Customer Reviews

Product Q&A

• Can I connect the Enerdrive B-tec Lithium Batteries in Parallel or in series?

  Hi there,

  You cannot connect any of the EnerdriveB-TEC batteries in series. You can however connect up to two only of the same size (ah) B-TEC batteries in Parallel. Enerdrive recommend that you only do this if you don't over load the max current of the internal BMS board from ONE OF THE BATTERIES.

  Example. If you connect 2 x 200Ah B-TEC batteries then do not draw more than 200A of DC current from that battery bank, as one (1) single 200Ah B-TEC battery is only capable of handling 200A DC.

  The main aim of connecting two (2) of the Enerdrive B-TEC batteries is not to increase your maximum DC current output, but to double your storage capacity.

  Double the storage equals double the time you can stay powered up and off the grid.

  Be sure to always consult the Enerdrive user manuals for correct cable sizing, fuse sizing and wiring diagrams.

  We now sell an Enerdrive battery bundle with a parallel kit - please CLICK HERE to find it.

• Can I series connect B-TEC batteries to achieve higher voltage?

  No. Enerdrive oers higher voltage Lithium solutions - contact us for details.

• Can I use an Inverter with my B-TEC battery?

  Yes. Refer to Section 4 of the manual for more detail.

• Can I install the B-TEC battery in a wet area?

  No. Due to the construction of the B-TEC cases the batteries must be installed in a dry environment to protect against moisture ingress.

• Can I parallel B-TEC batteries?

  The short answer is yes. The long answer is - make sure the link cables are of the same size or greater than your load/charging requirements and no more than 4 batteries in parallel.

  With low to medium current draw installations (the vast majority of applications) you may never see an issue and your storage capacity will be greatly increased - I.E. 2 x 200 Amp = 400 Amp capacity. When installing, fully charge the batteries separately - then let sit for 30 minutes before connecting together. When connecting in parallel - take the positive from Battery 1, and the negative from Battery 2 to your system as per the diagram below.

  

  The Smart Phone App will only show the information from one battery at a time - not both. This is another advantage of a separate Battery Monitor - it will show the total system environment.

  *Note: Slight variance of State of Charge or Amps may occur between the batteries in parallel however these should not vary by more than 5%. It is recommend that annually the batteries be disconnected and individually charged allowing them to sit at a fully charged state for 12hrs each before connecting back together.

• Can I install the B-TEC battery on its side or end?

  No. Please note that the 12V 200Ah SLIM B-TEC Battery features a wider range of acceptable mounting orientations - please refer to the diagram below for guidance.

Warranty

Delivery